CONSTRUCTION · INDUSTRIAL & SPECIALTY · FOR SAFETY LEADERS
Construction Safety Software
Your Crews Will Actually Use.
On an industrial jobsite, the pre-task plan that gets skipped is the one that mattered. Field1st is built for industrial and specialty contractors and the subs on every site: voice-first PTPs and JHAs every crew will finish, AI that flags the Focus Four from a photo, and real-time visibility across every trade and employer on the job — so the plan actually gets followed.
A 20-minute walkthrough built around your pre-task plans and your subs. No slides, no prep.
START HERE
What Is Construction Safety Software?
Construction safety software helps industrial, specialty, and general contractors and their subs run pre-task plans, JHAs, inspections, toolbox talks, and incident reporting on the jobsite — and gives leaders real-time visibility across crews and subs.
The difference is whether crews actually use it. Field1st is voice-first and built for the field, so a pre-task plan or JHA gets completed at the work area — gloves on, in under 90 seconds — instead of skipped or back-filled at the trailer. That means higher field adoption, the Focus Four caught before work starts, every sub on one process, and superintendents who can see the whole site in real time.
Who It's For
• Industrial & specialty contractors
• General contractors & construction managers
• Specialty trades & self-perform crews
• Subcontractors on every jobsite
• Superintendents & site safety leaders
START WHERE IT HURTS MOST
Six Jobsite Problems, Solved at the Point of Work.
Each of these is where a construction safety program loses adoption, loses a sub, or misses the hazard. Here's what Field1st does about each.
01
GUEST ACCESS
Subs Won't Use Your System
Subcontractors won't buy a seat or learn your app. Field1st gives them QR guest access to complete your PTP or JHA in minutes — no seat, full visibility for the GC.
02
VOICE1ST
Pre-Task Plans Get Skipped
Voice1st lets crews speak through the PTP in under 90 seconds at the work area, gloves on. Completion jumps because it doesn't slow the pour, the lift, or the tie-in.
03
AI HAZARDID
The Focus Four Gets Missed
A photo flags fall, struck-by, caught-in, and electrocution hazards and recommends the control — giving a tired crew a second set of eyes before work starts.
04
AI SAFETY AGENT
Near Misses Go Unreported
One-tap near-miss capture with voice narration, and an AI Safety Agent that follows up and surfaces the pattern before it becomes a recordable.
05
PULSE1ST ANALYTICS
No Visibility Across Trades and Sites
Real-time leading-indicator dashboards across every crew, sub, and project — so you spot hazard trends by trade or site before they become incidents.
06
CORRECTIVE ACTIONS
Corrective Actions Die in a Binder
Assign, track, and escalate corrective actions to closeout across every crew and sub, so open items are visible — not buried in a daily report.
Recognize Your Jobsite in Any of Those?
See the fix in 20 minutes — built around your pre-task plans, your inspections, and your subs.
A DAY ON SITE
How Field1st Runs From First Light to Closeout.
Safety in the flow of the work — not a binder someone fills out at the trailer.
01
6:30 AM · MORNING HUDDLE
Pre-Task Plans, by Voice
Each crew talks through the PTP at the work area. Voice1st captures the task, crew, hazards, and controls, and the superintendent sees every plan roll in, live.
02
9:15 AM · ON THE DECK
A Sub Flags a Fall Hazard
A subcontractor snaps a photo of an unprotected edge. HazardID flags the fall exposure and recommends the control; the AI Safety Agent attaches the right procedure.
03
11:40 AM · WALKTHROUGH
Inspection Without the Clipboard
The safety lead walks the site, capturing findings by photo and voice. Corrective actions are structured, assigned, and routed automatically — no typing up notes later.
04
2:20 PM · FOLLOW-UP
The Corrective Action Closes
The assigned foreman gets the item, fixes the guardrail, and closes it out on mobile. Nothing waits for the end-of-week meeting.
05
4:45 PM · CLOSEOUT
The Day, on One Dashboard
The safety manager sees adoption, hazards, near misses, and closeout across every trade and project — and tomorrow's plan starts with today's lessons.
BUILT FOR THE JOBSITE
The Construction Workflows, Digitized and Voice1st.
Field1st runs the safety workflows industrial, specialty, and general contractors already use — completed by voice and photo, visible in real time.
01
PRE-TASK PLANS & JHAS
Before the Work Starts
Crews and subs complete PTPs and JHAs by voice at the work area, signed and stored before the job begins.
02
SITE INSPECTIONS
Construction Inspection Software
Run inspections and observations by photo and voice; findings and corrective actions structure and route themselves.
03
TOOLBOX TALKS
Consistent Across Crews
Deliver and document toolbox talks and daily huddles, with attendance and sign-off captured in the flow.
04
ORIENTATIONS & INDUCTIONS
Onboard Fast
Site orientations and inductions for new hires and subs, so everyone starts aligned to the site's rules.
05
PERMITS
Hot Work, Excavation, Confined Space
Dynamic permits route for approval and escalation, so the right control is set before high-risk work starts.
06
NEAR-MISS & INCIDENT
Catch It Early
Low-friction voice reporting drives the near-miss volume that gives leaders real leading indicators.
AI HAZARD RECOGNITION
A Second Set of Eyes on the OSHA Focus Four.
Add a photo to any pre-task plan or inspection and HazardID flags the four hazards that cause the most construction fatalities — and recommends the control before work starts.
Falls
Unprotected edges, openings, ladders
Struck-By
Equipment, loads, flying objects
Caught-In / Between
Trenches, equipment, materials
Electrocution
Lines, temp power, unsafe proximity
ALIGNED TO THE STANDARDS YOU'RE AUDITED AGAINST
Free white paper FOR SAFETY LEADERS
The Contractor Safety Gap: Who is actually on your site today, and can you prove it?
The Contractor Safety Gap White paper breaks down why your highest-risk crews are the ones your system can't see, what the controlling-employer duty actually requires, and how to score your own coverage in a single shift.
SUBCONTRACTOR SAFETY MANAGEMENT
Your Jobsite Is Only as Safe as Your Subs.
Most jobsite incidents involve subcontractors — and most safety tools price them out or leave them on paper. Field1st brings every trade on site onto one process, without buying everyone a seat.
01
QR + MAGIC LINK
Onboard in Minutes
A sub scans the form's QR code, gets a magic link, and completes the PTP or JHA on their phone — no seat, no app rollout.
02
GUEST PROFILES
Controlled, Not Wide Open
Guests create a temporary profile, optionally gated by a company code, and appear in your list flagged as contractors.
03
FULL VISIBILITY
One Source of Truth
See exactly who accessed and completed every form, across every trade on the jobsite, in one place.
THE OUTCOME
From Paper Pre-Task Plans to Prevention.
Metrics from Field1st deployments across construction and field operations.
CONSTRUCTION QUESTIONS
Frequently Asked Questions.
What Is Construction Safety Software?
Construction safety software helps general contractors and subcontractors run pre-task plans, JHAs, inspections, toolbox talks, and incident reporting on the jobsite, and gives leaders real-time visibility across crews and subs. Field1st is built for the field, so crews actually use it.
How Does Field1st Handle Subcontractor Safety?
Every form has a QR code, and with guest access enabled a subcontractor can scan it, receive a magic link, and complete the pre-task plan or JHA without a paid seat — while the GC keeps full visibility into who did what.
Is There a Per-Seat Fee for Subcontractors?
No. Subcontractors join through QR and magic-link guest access with no paid seat, so the GC can bring every trade onto one safety process without a per-user cost.
Does Field1st Cover the OSHA Focus Four Hazards?
Yes. AI hazard recognition and pre-task planning help crews catch fall, struck-by, caught-in/between, and electrocution hazards — and recommend controls — before work starts.
Is There Construction Inspection Software Included?
Yes. Field1st runs site inspections and observations by photo and voice, structures findings and corrective actions automatically, and routes them to closeout.
Does Field1st Give Superintendents Real-Time Visibility?
Yes. Superintendents and safety leaders see pre-task plans, hazards, near misses, inspections, and corrective-action closeout across every trade and project in real time, with leading-indicator dashboards by crew, sub, and site.
Will Crews and Subs Actually Use It?
Yes. Voice1st lets crews and subcontractors complete a pre-task plan or JHA by speaking, gloves on, at the work area in under 90 seconds — so completion happens in the flow of work instead of being skipped or back-filled at the trailer.
Does It Work Offline on the Jobsite?
Yes. Crews capture pre-task plans, JHAs, and inspections in zero-signal environments, and everything syncs when the device is back online.
Bring One Pre-Task Plan.
We'll Show You the Rest.
A 20-Minute Walkthrough Built Around Your Pre-Task Plans, Inspections, and Subs.
Hand us one form your crews or subs use today. In 20 minutes you'll watch it come alive in Field1st — voice capture, AI hazard review, and the real-time dashboard your superintendents and safety leaders would see. No slides. No prep. No commitment.